Featured Specials
We have acquired the following equipment from a technical college’s welding lab. All units have “LH” serial numbers (manufactured 2007). This equipment carries a 90 day warranty. These are actual pictures.
Miller Dynasty 200DX TIG Welder
- First Generation units
- Single or three- phase input, 115-460 volts,
automatic input voltage linking - AC or DC Stick or TIG welding
- High freq impulse or Lift arc start
- Stick DIG control
- AC TIG square wave output, adjustable frequency
and balance - DC TIG Flat output
- DC TIG Pulsed output, adjustable peak and background amps, adjustable frequency
New Unit List: $3,754.00
New Unit OTC: $3,135.00
Eleven used units @ $2,000.00 each !!!!
90 day warranty
Miller XRA Python Pull Gun - 25 ft.
- 200 amp @ 100% duty cycle
- Air- Cooled
- 030”- 1/16” Aluminum wire
- Compatible with Millermatic 350P and XR Controls
New Unit List: $2,465.00
New Unit OTC: $2,059.00
One used available @ only $653.00!!
90 day warranty
Miller XRA Aluma-Pro Pull Gun - 15 ft.
- 300 amp @ 100% duty cycle
- Air- Cooled
- 030”- 1/16” Aluminum wire
- Compatible with Millermatic 350P, XR-S/D Control,
XR Aluma Feed Control, some XR-A controls
New Unit List: $1,975.00
New Unit OTC: $1,650.00
Five used available @ $1,125.00 each
90 day warranty
Miller SSW-2020ATT Spotwelder
- Requires 230 volt single phase input @ 90 amps
- Water- Cooled: Requires optional coolant recirculator
- Requires 60 psi compressed air
- 20 KVa output: 9,000 amps with 18” tongs (STD.)
12,500 amps with optional 6” tongs - Adjustable tong pressure
- Adjustable tong speed
- Adjustable weld time
- Adjustable weld amperage
New Unit List: $5,886.88
New Unit OTC: $4,911.00
One used unit @ $3,140.00
90 day warranty
Miller Contractor Kits
- EVERYTHING YOU NEED TO GET THAT DYNASTY
200DX UP AND RUNNING EXCEPT THE ARGON! - 150 amp Weldcraft air-cooled TIG torch
- TIG torch accessory kit
- Remote foot control
- Argon regulator and hose
- Stick electrode holder and cable
- Carrying case
New Unit List: $812.00
New Unit OTC: $678.25
Fifteen used unit @ $420.00 each
Jancy MT35v2 Mag Drill
- 120 volt, 1400 watt motor
- Digital rpm display
- Dual Speed Range:
- Variable 70-170 rpm
- Variable 140-340 rpm
- Up to 2.5 inch diameter hole capacity, 2” max, depth
- 4000 lb. - pull electromagnetic base on 1” carbon steel
Suggested List: $1,8954.00
One only: $1,520.61
Madison
101 S. Dickinson St.
Madison, WI 53703
Phone: (608) 257-5606
Fax: (608) 257-0074
Toll-Free Phone:
(800) 536-3355
Monday — Friday:
7:30 a.m. to 5 p.m.
Mineral Point
620 Dodge St.
Mineral Point, WI 53565
Phone: (608) 987-2341
Monday — Friday:
7:30 a.m. to 5 p.m.
Tips & FAQs
- You guys are open from 7:30 am to 5:00 pm Monday through Friday. Why can’t you refill my kegerator carbon dioxide cylinder after 4:30 pm?
And why does a “while-I wait-fill” of this cylinder cost me an extra ten bucks? - What pressure settings should I use for my oxygen and fuel gas regulator.
- Are all flux-cored MIG wires gasless?
- My compressed-air plasma cutter goes through a lot of tips and electrodes! How can I minimize this?
What's New
Pipe Welders!
Remember this gun? Bernard no longer makes it! CM Industries does! And we can get you one!
Call us with your wire feeder model, and we will quote you.